Professional Underfloor Heating solutions in Galway by Finvarra Ltd. 30+ years of experience. Honest, reliable, local experts.
What is underfloor heating?
Underfloor heating is a heating system that warms a room from the floor up, using pipes hidden beneath the floor surface instead of radiators on the walls. Warm water flows through the pipes, the floor heats gently, and the whole floor becomes one large, low-temperature radiator.
In most Irish homes the system is water-based, often called a wet system. Loops of tough plastic pipe are laid across the floor on top of insulation, then covered with a layer of screed, which is the smooth cement layer your tiles or timber floor sits on. Each room has its own loop, and all the loops run back to a central point called a manifold, where the flow to each room is controlled.
The heat feels different from radiators. A radiator heats the air around it, so the room is warmest beside the radiator and cooler across the far side. Underfloor heating spreads the warmth evenly across the whole room, with no cold corners and a warm floor under your feet. This beginner's guide to underfloor heating describes how the floor itself becomes the heat emitter.
It also runs at a much lower water temperature. Underfloor heating typically needs water at around 35 to 45°C, where radiators on a boiler are usually run far hotter. That is why underfloor heating and heat pumps are such a good match, since a heat pump is at its most efficient when making low-temperature water.
There are practical benefits too. With no radiators, you get your wall space back and can put furniture wherever you like. There are no hot surfaces for small children to touch, and less dust is moved around the room.
Underfloor heating is now standard in most new homes in Ireland, and it can also be fitted in extensions, renovations and existing rooms using slimmer systems made for that job.
At Finvarra Ltd, we design and install water-based underfloor heating for homeowners across Galway and the surrounding areas, on its own or as part of a full heat pump system.
How does underfloor heating actually work?
Underfloor heating works by pumping warm water through loops of pipe under the floor, so the floor gives off a steady, gentle heat into the room. A few key parts make that happen.
The heat source. Something has to warm the water. In most new systems that is an air-to-water heat pump. An existing boiler can also do the job, with the water temperature turned down before it reaches the floor.
The manifold. This is the control centre, usually fixed to a wall in a hot press or utility room. Warm water arrives at the manifold and is shared out to each loop of pipe. Every room has its own loop, and small valves on the manifold open and close to send heat only where it is needed.
The mixing valve and pump. Where the heat source produces water that is too hot for a floor, a mixing valve blends it down to a safe temperature. A pump keeps the water moving around the loops.
The pipes. Continuous lengths of plastic pipe are laid in a pattern across each room, fixed down on top of floor insulation. There are no joints under the floor. The insulation underneath stops the heat going down into the ground, so it travels up into the room.
The screed. The pipes are covered in screed, which soaks up the heat and spreads it evenly across the floor. This underfloor heating guide explains how the screed helps to spread heat across the whole surface.
The thermostats. Each room or zone has its own thermostat. When a room drops below the set temperature, the thermostat tells the manifold to open that room's loop.
Because the floor and screed hold a lot of heat, the system warms up and cools down slowly. It works best left on at a steady temperature and trimmed with the thermostats, not switched on and off like a boiler with radiators.
The result is an even, comfortable warmth in every room. At Finvarra Ltd, we design each system around the heat loss of the rooms, so the pipe spacing, water temperature and controls are right for your Galway home from the first day.
What types of underfloor heating are available?
There are two main types of underfloor heating, water-based and electric, and within water-based systems there are several ways of fitting the pipes. The right one depends on whether the house is a new build, a renovation or an existing home.
Water-based (wet) systems. Warm water runs through pipes under the floor, fed by a heat pump or boiler. This is the type used to heat whole houses, because it is cheap to run, and it is the type Finvarra Ltd installs.
Electric systems. Thin heating cables or mats sit under the floor finish and run off the electricity supply. They are simple to fit in a single small room such as a bathroom, but cost more to run, so they are rarely used as the main heating for a house. This guide to electric and water underfloor heating compares the two.
Within water-based systems, the main options are:
Pipes in screed. The standard method for new builds, extensions and floors that are being dug out. Pipes are fixed to floor insulation and covered with screed. It gives the best heat output and suits a heat pump very well.
Low-profile overlay systems. Made for existing houses. Slim grooved boards hold the pipes and sit directly on top of the current floor, adding only a small amount of height. There is no digging out and little or no drying time.
Systems for timber floors. In upstairs rooms or houses with suspended timber floors, pipes can be fitted between or over the joists, using metal plates to spread the heat.
Mixed systems. Many homes have underfloor heating downstairs and radiators upstairs. The two run as separate zones from the same heat source.
Single-room systems. A kitchen extension or sunroom can be given underfloor heating on its own and connected into the existing heating.
Each type has its place. A new build in the county will almost always use pipes in screed. A kitchen renovation in an older house in Galway is more likely to suit a low-profile system.
We look at your floors, your ceiling heights and your heat source before we recommend one, so the system fits the house.
What makes underfloor heating different from other plumbing and heating services?
Underfloor heating is different because it is built into the fabric of the house. A radiator, a cylinder or a boiler can be reached, repaired or replaced at any time. Underfloor pipes are buried under screed and flooring for the life of the building, so the design and installation have to be right the first time.
It is designed before it is fitted. Each room's heat loss is worked out first. That decides how close together the pipes are laid, how many loops each room needs and what water temperature the system runs at. Fitting pipe without a design is the most common reason underfloor heating disappoints.
It is tied into the building work. Most plumbing jobs are done by one trade on one visit. Underfloor heating has to be timed around floor insulation, screed, drying time and floor finishes. It needs close coordination with the builder, the screeder and the flooring fitter.
There is one chance to test it. The pipes must be pressure tested before the screed is poured, and kept under pressure while it goes down. A leak found afterwards means breaking out the floor. This building control guidance on underfloor heating lists poor installation and not enough screed drying time among the common causes of failure.
It runs differently. Underfloor heating uses low-temperature water and responds slowly. The controls, mixing valve and pump have to be set up to suit, and the homeowner needs to be shown how to run it.
The floor finish is part of the system. Tiles, timber, vinyl and carpet all let heat through at different rates. The flooring has to be considered in the design, which is never a concern with radiators.
It pairs closely with the heat source. Underfloor heating and a heat pump work as one system. Designing them together gives lower running costs than treating them as two separate jobs.
Finvarra Ltd is a plumber-led company that installs heat pumps and underfloor heating. We understand the pipework, the heat source and the controls, so one team takes responsibility for the whole system in your Galway home.
What should homeowners know before starting an underfloor heating installation?
Before you start, the main thing to know is that underfloor heating has to be planned early. It affects floor levels, insulation, the building schedule and your choice of flooring, so it is far easier to get right at the design stage than to add once work is under way.
Floor height matters. A standard system needs room for insulation, pipes and screed. In a new build or extension that is allowed for in the plans. In an existing room, a low-profile system adds a small amount of height, which can affect doors, skirting, stairs and kitchen units.
Insulation under the pipes is essential. Without good floor insulation, heat goes down into the ground and the system costs more to run. In an older house, this is often the deciding factor between digging out the floor and laying a system on top.
It takes longer to respond than radiators. Underfloor heating warms up slowly and holds its heat. It suits rooms that are used every day and kept at a steady temperature.
Your floor covering affects performance. Tile and stone are the best. Engineered timber, laminate and vinyl work well if they are rated for underfloor heating. Thick carpet and underlay hold the heat back.
Screed needs time to dry. A traditional screed can take weeks to dry before flooring goes down, and the heating must not be used to rush it. Build this into your schedule.
Existing radiators can stay elsewhere. You do not have to do the whole house. This article on retrofitting underfloor heating explains how a single zone can be tied into an existing radiator system.
Think about your heat source. Underfloor heating works with a boiler, but it is at its best with a heat pump. If a heat pump is in your plans for the next few years, design the floor for it now.
Decide where the manifold will go. It needs a spot that is central, hidden and easy to reach.
Ask about the grant. There is no grant for underfloor heating by itself, but it can count towards the heating upgrade part of the SEAI heat pump grant.
Finvarra Ltd will go through each of these points at the survey, so you know what is involved in your Galway home before any floor is lifted.
How much does underfloor heating cost in Galway?
Underfloor heating in Galway typically costs somewhere between €2,000 and €15,000, depending on how much floor is being heated and whether it is going into a new floor or an existing one. A single room or small extension sits at the lower end. The full ground floor of a house, or a retrofit where floors have to come up, sits at the higher end.
These are the things that move the price.
Floor area. More square metres means more pipe, more insulation and more labour. The cost per square metre usually falls as the area grows, because every job needs a manifold, pump and controls regardless of size.
New floor or existing floor. Fitting pipes into a new build or extension, where the floor is being built anyway, is the cheapest route. Retrofitting costs more, because old floors have to be lifted or a low-profile system laid on top.
Type of system. Pipes in screed use simple materials. Low-profile overlay boards cost more to buy but save on digging out and drying time.
Number of rooms and zones. Each room normally has its own loop and thermostat. More zones give better control and add to the cost.
Floor insulation. If the existing floor has little or no insulation, adding it is an extra cost, but it is money well spent.
Heat source. Connecting to a heat pump that is being fitted at the same time is simple. Tying into an existing boiler needs a mixing valve and pump set.
Screed and floor finishes. Check whether your quote includes screed. New flooring is almost always a separate cost.
There is no stand-alone grant for underfloor heating. If it is installed as part of a heat pump system, it can count towards the heating upgrade part of the SEAI heat pump system grant, worth up to €2,000 within a total of up to €14,500 for a qualifying house.
Running costs are where underfloor heating earns its keep. Because it uses low-temperature water, a heat pump feeding underfloor heating is one of the cheapest ways to heat a well-insulated home.
Every house is different, so the only reliable figure is one based on your rooms. Finvarra Ltd will measure up and give you a clear written price for your Galway home.
What are good brands for underfloor heating
Good underfloor heating brands are the ones that supply a complete, matched system, with quality pipe, a solid manifold, proper controls and a long warranty on the pipe. The pipe will be under your floor for decades, so this is not the place to cut corners.
Firebird. Firebird is an Irish manufacturer best known for its boilers, and it also makes the Enviroair range of heat pumps and underfloor heating. Its Enviroair underfloor heating systems are designed to work with Firebird heat pumps, which makes for a well-matched setup from one supplier.
Other established names. Uponor, Rehau and Polypipe are long-standing pipe system manufacturers with underfloor heating ranges for new floors and for renovations. You will see their names on many Irish sites.
The brand on the box matters less than what is in it. These are the things worth checking.
Pipe quality. Look for pipe with an oxygen barrier, which protects the rest of the heating system from rust, and a long manufacturer's warranty.
The manifold. A good manifold has a flow meter on each loop, so the system can be balanced properly, and valves that can be serviced.
Controls. A thermostat in each room or zone gives the best comfort and the lowest bills. Smart controls let you adjust rooms from your phone.
A design service. Reputable suppliers provide a pipe layout drawn for your house, showing loop lengths and spacing for each room. Be wary of any system sold without one.
The right system for the floor. A good range will include pipes-in-screed for new floors and a low-profile option for existing ones.
Compatibility with your heat source. The system should be designed for the water temperature your heat pump or boiler will supply.
Support in Ireland. Parts and technical help should be easy to get, now and in twenty years.
One point matters more than any brand name: underfloor heating is only as good as its design and installation. Quality pipe laid at the wrong spacing, or on poor insulation, will never heat the room properly.
At Finvarra Ltd, we use proven components and design every system around the house, so what goes under your floor in Galway is built to last.
Does my existing system impact an underfloor heating installation
Yes. Your existing heating and your existing floors both affect how underfloor heating is designed and what it costs. Underfloor heating has to connect to a heat source and sit within a floor, so what is already there shapes the job.
Your heat source. A heat pump produces low-temperature water, which is exactly what underfloor heating needs, so the two connect simply. Firebird notes that its Enviroair heat pump can be combined with underfloor heating, or with a mix of underfloor heating and radiators. A boiler makes much hotter water, so a mixing valve and pump are fitted to bring it down to a safe temperature for the floor.
The size of the heat source. Adding underfloor heating to an extension adds to the heating load. We check that your heat pump or boiler has the capacity for the extra area.
Your existing radiators. They can stay. Underfloor heating in one part of the house and radiators in another run as two zones, each with its own controls and water temperature.
Your floors. This is the biggest factor in an existing house. A solid concrete floor with no insulation may need to be dug out, or covered with an insulated low-profile system. A suspended timber floor needs a different method again. Ceiling heights, door thresholds and stairs all limit how much the floor can be raised.
Pipework routes. Flow and return pipes have to run from the heat source to the manifold. In a finished house, we plan the least disruptive route.
The condition of the system. Old radiator systems often carry rust and sludge. The system is flushed and a filter fitted before the new floor circuits are connected, so the fine underfloor pipes and valves are protected.
Controls. Older timers and thermostats are usually replaced or extended so each underfloor zone has its own thermostat.
Future plans. If you intend to move to a heat pump later, tell us now. We can design the underfloor heating for low-temperature water, so it is ready when the heat pump goes in.
Because Finvarra Ltd works on whole heating systems, we can tell you honestly what your Galway home needs for underfloor heating to work well with what you already have.
What's included in the cost of underfloor heating?
A proper underfloor heating price covers everything from the design to a working, tested system, but it rarely covers the building work around it. Knowing where that line falls is the key to comparing quotes fairly.
A full installation would normally include:
Survey and design. Measuring the rooms, working out the heat loss and drawing the pipe layout, with loop lengths and pipe spacing for each room.
Pipe. All the underfloor heating pipe, laid in continuous loops with no joints under the floor.
Fixings or panels. Clips, rails or grooved boards to hold the pipe in place, and edge insulation strip around the walls.
Manifold. The manifold, with flow meters and valves for every loop, mounted and connected.
Pump and mixing valve. Where the heat source needs them, to control the water temperature going to the floor.
Controls. A thermostat for each zone, the wiring centre and the valve actuators on the manifold.
Connection to the heat source. Flow and return pipework from your heat pump or boiler to the manifold.
Pressure testing. Testing the pipework before the screed goes down and keeping it under pressure while the floor is finished.
Commissioning. Filling, venting and balancing each loop, setting the water temperature, and bringing the floor up to heat gradually.
Handover. Showing you how the thermostats work and how to run the system day to day.
These are often priced separately or carried out by your builder, so ask about each one:
Floor insulation. Sometimes included, sometimes left to the builder.
Screed. Usually poured by a screed contractor.
Removing old floors. Digging out or lifting existing floors in a retrofit.
Floor finishes. Tiles, timber or vinyl, and the fitting.
Electrical work. The power supply to the controls.
Making good. Skirting, doors and decoration afterwards.
For a wider view of what goes into a retrofit budget, this guide on the cost of retrofitting underfloor heating is a helpful read.
Ask for the quote in writing with each item listed. At Finvarra Ltd, our quotes set out in plain language what is included and what is left to others, so there are no surprises once the work starts.
Don't rely on rough guesses for underfloor heating costs. Get a proper assessment. We can often give you an initial idea over the phone after a few questions about your home and current heating, or we'll arrange a free site visit to give you accurate pricing for your Galway home.
Don't rely on rough guesses for oil boiler costs. Get a proper assessment — we can often give you an initial idea over the phone after a few questions about your home and current boiler, or we'll arrange a free site visit to give you accurate pricing for your home.
Should I consider underfloor heating?
You should consider underfloor heating if you are building, extending or renovating, or if you are planning a heat pump. Those are the moments when floors are open or the heating is being redesigned anyway, so underfloor heating can go in for the least cost and disruption.
Underfloor heating is likely to suit you if:
You are building a new home. It is the natural choice for a new build. The floor is designed for it from the start, and it pairs with the heat pump most new homes now have.
You are adding an extension. A new kitchen, living area or sunroom has a new floor, so the pipes can go in before the screed.
You are renovating downstairs. If old floors are being lifted for insulation or new tiles, it is the ideal time.
You are getting a heat pump. Underfloor heating lets a heat pump run at its lowest temperature, which keeps running costs down. Under the SEAI heat pump system grant, up to €2,000 is available for central heating upgrades such as radiators or underfloor heating.
You want open, uncluttered rooms. With no radiators, you are free to place furniture, units and glazing wherever you like.
You have tiled or stone floors. These can feel cold underfoot with radiators, and feel completely different with heat beneath them.
You use the rooms every day. Underfloor heating gives its best in kitchens, living rooms and family spaces that are kept at a steady temperature.
It may not be the right choice if:
The floors are staying as they are. Fitting it into a finished room with good flooring is disruptive, and upgrading the radiators may be the better answer.
The room is only used now and then. A guest room or occasional office is better served by a radiator that heats up quickly.
The house is poorly insulated. As with a heat pump, the heat has to stay in the room. Insulation comes first.
Floor height is very tight. Some older houses cannot take even a slim system without major changes to doors and stairs.
Many homes end up with a mix: underfloor heating in the main living areas and radiators elsewhere. That is a perfectly good system.
Finvarra Ltd will give you a straight answer on whether underfloor heating is worth it for your Galway home, or whether your money is better spent elsewhere.
What underfloor heating brands do you install in Galway
(Finvarra Ltd installs water-based underfloor heating using established, proven systems. Firebird is our first choice, especially where the floor is being paired with a Firebird Enviroair heat pump. We choose components for how well they will perform under your floor for decades, not for the name on the box.
Firebird. Firebird is an Irish manufacturer that many Galway households already know from their oil boiler. Its underfloor heating is designed to work with its Enviroair heat pumps and cylinders, so the heat source, manifold and controls come from one supplier and are built to work together. That gives you a well-matched system and one point of contact for parts and support.
Other proven systems. Where a job calls for something different, such as a very slim board for an existing floor or a system for suspended timber floors, we use components from established manufacturers with a track record in Irish homes.
Whatever the brand, every system we fit meets the same standard:
Pipe with an oxygen barrier and a long manufacturer’s warranty, laid in continuous loops with no joints under the floor.
A quality manifold with a flow meter on each loop, so every room can be balanced properly.
A thermostat in each room or zone, with smart controls available if you want to adjust the heating from your phone.
A pipe layout drawn for your house, with the spacing and loop lengths for each room based on its heat loss.
Parts and technical support available in Ireland, now and in years to come.
The right system for your home comes from the survey. It depends on:
Your floor. A new screed floor, an existing solid floor and a timber floor each suit a different system.
Your heat source. A system designed for a heat pump uses closer pipe spacing than one designed for a boiler.
Your floor height. Where every millimetre counts, a low-profile system is the answer.
Your budget. We explain the price difference between options and what you get for the money.
If you already have a brand in mind, or your builder has suggested one, tell us. We will give you a straight answer on whether it suits your floors and your heat source.
Because Finvarra Ltd installs heat pumps as well as underfloor heating, we match the floor system to the heat source from the start, so the whole system in your Galway home runs efficiently from day one.
How Long Does Underfloor Heating Take
Laying the underfloor heating pipes is quick, usually one to three days for a typical ground floor. The full job takes longer, because the floor has to be prepared beforehand and the screed has to dry afterwards. The overall time depends mostly on the type of system.
For a standard pipes-in-screed system, the stages are:
1. Survey and design. We measure the rooms and work out the heat loss, and the pipe layout is drawn up. Allow a week or two before work starts.
2. Floor preparation. The builder gets the sub-floor ready and the insulation is laid. In a retrofit, this is when old floors are lifted or dug out, which can add several days.
3. Laying the pipes. Pipes are fixed down in loops, room by room, and run back to the manifold. A single room takes a day or less. A full ground floor takes one to three days.
4. Pressure testing. The pipes are filled and tested before anything covers them.
5. Screed. The screed is usually poured in a day.
6. Drying. This is the longest stage. A traditional screed can need several weeks before floor coverings go down, and the heating should not be used to force it. Liquid and fast-drying screeds are quicker.
7. Connection and commissioning. The manifold is connected to the heat pump or boiler, the thermostats are wired, and each loop is balanced. This takes a day or two.
8. Gradual warm-up. The floor is brought up to temperature slowly over several days, to protect the screed and the floor finish.
9. Floor finishes. Tiles or timber go down once the screed is dry.
Low-profile retrofit systems are much faster. The boards sit on the existing floor, and there is little or no screed to dry. Uponor says its low-profile Minitec system is only 15mm thick and can be set up in three days.
In a new build or extension, the underfloor heating follows the building schedule, so we work to your builder's dates.
You can use the rest of the house as normal while the work is done, though the rooms being fitted will be out of use until the floor is finished.
Finvarra Ltd will give you a realistic timeline for your Galway home at the survey, including the drying time, so you can plan your flooring and your move back into the rooms.
Types of Underfloor Heating
The right type of underfloor heating depends on the floor it is going into. The idea is the same in every case, warm water in pipes beneath the floor, but the way the pipes are fitted changes with the building. These are the systems we fit most often around Galway, and where each one works best.
Pipes in screed on a solid floor. This is the standard system for new homes and extensions. Insulation is laid on the concrete sub-floor, the pipes are fixed to it, and a screed is poured over the top. It gives strong, even heat and holds its warmth well. It needs the most floor depth and a drying period, so it suits projects where the floor is being built from scratch.
Liquid screed systems. The same layout, but with a thinner, free-flowing screed that wraps closely around the pipes. It needs less depth, dries faster and responds a little quicker. It is popular in new builds and larger renovations.
Low-profile overlay systems. These are made for existing houses. Thin grooved boards carrying the pipes are laid straight over the current floor, so there is no digging out. One well-known example, Nu-Heat's LoPro10 system, is just 15mm thick and can go over solid or timber floors. They are the usual answer for a kitchen or living room renovation in an older home.
Between-joist systems. In houses with suspended timber floors, pipes are fitted between the joists with metal plates that spread the heat to the floorboards above. The floor level stays the same.
Upper-floor systems. Lightweight board systems allow underfloor heating upstairs, where a heavy screed is not practical. Many homes still choose radiators upstairs, as bedrooms need less heat.
Single-zone systems. One room, often a new extension, is given its own small manifold or control pack and connected to the existing heating.
Whole-house systems. Every room has its own loop and thermostat, all run from one or more manifolds. This is the norm in new builds with a heat pump.
Electric mat systems also exist for small rooms. They are fitted by electricians and tilers and cost more to run, so they are not what we install.
Finvarra Ltd will look at your floors and explain which type suits each room, and why, before you commit to anything.
How to Choose the Right Underfloor Heating Solution
Choosing the right underfloor heating comes down to matching the system to your floors, your heat source and the way you use the rooms. Get those three right and the system will be comfortable and cheap to run for decades. These steps will get you there.
Start with the floor. Is it a new floor, a solid floor being dug out, an existing floor staying in place, or a timber floor? That one answer narrows the choice of system more than anything else.
Check how much height you have. Measure what you can afford to lose at doors, stairs and kitchen units. If the answer is very little, a low-profile system is the route.
Put insulation first. Make sure there will be proper insulation under the pipes. Without it, a good share of your heat goes into the ground.
Insist on a design. The pipe spacing and loop lengths should come from a heat loss calculation for each room. Ask to see the layout drawing before work starts.
Match it to the heat source. Tell your installer what will be heating the water, now and in the future. A system designed for a heat pump uses closer pipe spacing than one designed for a boiler.
Decide on zones. A thermostat in every room gives the best control. Open-plan areas can share one.
Choose your flooring early. Tile, stone, engineered timber and vinyl all behave differently. Tell the designer what is going down, and check the flooring is rated for underfloor heating.
Look at the pipe. As one Irish supplier puts it, the pipework buried in the floor is the most critical component of an underfloor heating system. Ask about the make and the warranty.
Plan the manifold position. It should be central, accessible and out of sight.
Think about the whole house. Underfloor heating downstairs with radiators upstairs is often the best balance of comfort and cost.
Compare quotes like for like. Check each quote for insulation, screed, controls, commissioning and connection to the heat source.
Do not choose on price alone. A cheap system with too little pipe or poor controls will cost you more to run every winter.
Finvarra Ltd will walk you through each of these points at the survey. You will know which system suits your Galway home, what it will cost and how long it will take before you decide.
What Are the Reasons to Hire a Professional for Underfloor Heating Solutions?The main reason to hire a professional is that underfloor heating is buried under your floor for the life of the house. Once the screed is poured and the tiles are down, a mistake cannot be put right without breaking out the floor. It has to be designed, installed and tested properly the first time.
The design decides whether it works. Pipe spacing, loop lengths, flow rates and water temperature all have to be calculated for each room. A professional designs the system around the heat loss of your house. Guesswork leaves you with rooms that never get warm.
Leaks have to be found before the floor is closed. A professional pressure tests every loop before the screed is poured and keeps the pipes under pressure while it goes down. That simple step prevents the most expensive failure there is.
The manifold is skilled plumbing. Connecting the manifold, mixing valve, pump and heat source is not a DIY task. Even guides written for self-builders say the manifold should be installed by a professional.
It has to work with your heat source. Underfloor heating must be matched to your heat pump or boiler, with the right temperatures and controls. A plumber who understands both makes them work as one system.
Commissioning protects your floor. The loops have to be flushed, vented and balanced, and the floor warmed up gradually. Rushing this can crack screed and damage floor finishes.
Coordination saves time and money. A professional works with your builder, screeder and flooring fitter, so each stage happens in the right order.
Warranties depend on it. Pipe and component manufacturers expect their systems to be installed to their instructions. Poor installation can leave you without cover.
It affects your grant. If underfloor heating is part of a heat pump project, the work has to be carried out by an SEAI registered contractor for the grant to be paid.
You have someone to call. If a room is not heating as it should in five years' time, you want the person who designed and fitted the system.
Finvarra Ltd is SEAI registered and plumber-led. We design, install and commission underfloor heating as part of the whole heating system, for homeowners across Galway and the surrounding areas.
When you’re comparing plumbing and heating contractors, the credentials can be confusing. One matters most: SEAI registration. It isn’t just a logo on a van. SEAI registration means your installer is on the official register, and it is what gives you access to government grants for heat pumps and heating upgrades.
For property owners in Galway, checking that your plumber is SEAI registered is essential. It means the work meets the required standards, your home is protected from costly mistakes, and you can claim the grants you’re entitled to.
In addition to our primary expertise, we specialise in tailored Plumbing and Heating solutions. This includes expert oil boiler replacement servicing & repairs solutions designed for residential properties across the greater Galway region. Government grants and financial incentives may also be available to you. Discover our complete range of services here.
Real jobs we’ve done over the past few years, for people who wanted air-to-water heat pumps, underfloor heating, or central heating repairs & fault finding.We deliver premium solutions paired with public sector knowhow, whether you need to navigate Plumbing and Heating government funding programs or get in touch with local county council chambers for best practices and expert advice. From residential Plumbing and Heating services throughout Galway, these are actual customers from Galway and the surrounding areas that we work with every week.

At Finvarra Ltd, we know how stressful it can be when things go wrong. That is why we are always on hand to get things sorted quickly and professionally, no matter the size or complexity of the task. Whether you need a air-to-water heat pumps,underfloor heating, or central heating repairs & fault finding, we have you covered. We show up, we do the job right, and we leave your property clean and tidy. Fully certified, and insured for your complete peace of mind. Over 30+ years of industry experience you can truly rely on. You can count on our local, experienced team to treat your property with care and deliver the professional, dependable service you expect and deserve.
Copyright 2026. Finvarra Ltd. All Rights Reserved.